• For vertical and horizontal mounting of safety switches TP...A, STA, STP and TX

The mounting plates are used for fastening safety switches TP...A, STA, STP and TX to safety guards. The safety switches can be attached vertically and horizontally.

Note

• Mounting plate material: galvanized St37.

Mounting example, safety switch vertical

Order numbers:

• 093 456 EMP-SB

• For vertical and horizontal mounting of safety switch TZ

The mounting plates are used for fastening safety switches TZ to safety guards. The safety switches can be attached vertically and horizontally.

The mounting plate EMP-SA is also suitable for safety switches with escape release from the rear.

Note

• Mounting plate material: galvanized St37.
• The mounting plate EMP-SA is also suitable for the safety switches TZ...C1684, TZ...C1815 and TZ...C1828 with escape release from the rear.

Mounting example, safety switch vertical

Order numbers:

• 094 401 EMP-SA

• For vertical and horizontal mounting of safety switches NM, NP...AS and NZ

The mounting bracket is used for fastening safety switches NM, NP...AS and NZ to safety guards. The safety switches can be attached horizontally or vertically.

Note

• Mounting plate material: galvanized St37.

Order numbers:

• 085 753 EMP-SC

The mounting plates are used for fastening actuators to safety guards. The safety switches can be attached vertically and horizontally.

Note

• Mounting plate material: galvanized St37.

Order numbers:

• 093 457 EMP-B1

The mounting plates are used for fastening actuators to safety guards. The safety switches can be attached vertically and horizontally.

Note

• Mounting plate material: galvanized St37.

Order numbers:

• 093 458 EMP-B2

• Material stainless steel

Installation example mounting plate EMP

Hinged door

Sliding door

Order numbers:

• 099 425 EMP-L-CEM05

• Material stainless steel

Installation example mounting plate EMP

Hinged door

Sliding door

Order numbers:

• 100 110 EMP-B-CEM05

• Mounting plate for safety switch CET for hinged or sliding doors
• Suitable for aluminum profiles 40 ... 45 mm
• Horizontal and vertical mounting
• Made of aluminum
• Suitable for CET with escape release

Installation example mounting plate EMP

Hinged door

Sliding door

Order numbers:

• 106 695 EMP-L-CET

• Mounting plate for actuator CET for hinged or sliding doors
• Suitable for aluminum profiles 40 ... 45 mm
• Horizontal and vertical mounting
• Made of aluminum
• Suitable for CET with escape release

Installation example mounting plate EMP

Hinged door

Sliding door

Order numbers:

• 106 694 EMP-B-CET

• Easy and quick mounting (only two screws required)
• Quicker module replacement
• Robust stainless steel plate
• Suitable for doors hinged on the right or left

Mounting plate for evaluation module

Suitable for all interlocking or locking modules in the system families AR and AP. 2 screws are sufficient for fastening the mounting plates.

Important:Only use if the handle module is also fastened to a mounting plate.

Order numbers:

• 109 490 MGB-A MOUNTING PLATE L-109490

• Easy and quick mounting (only two screws required)
• Quicker module replacement
• Robust stainless steel plate
• Suitable for doors hinged on the right or left

Mounting plate for handle module

Suitable for all MGB handle modules. 2 screws are sufficient for fastening the mounting plates.

Important:Only use if the evaluation module is also fastened to a mounting plate.

Order numbers:

• 109 491 MGB-A MOUNTING PLATE H-109491

• Easy and quick mounting (only two screws required)
• Quicker module replacement
• Robust stainless steel plate
• Suitable for doors hinged on the right or left

Mounting plate for escape release

Suitable for all MGB escape releases. 2 screws are sufficient for fastening the mounting plates.

Important:Pay attention to length of the escape release axis! You may need a longer axis

Order numbers:

• 109 492 MGB-A MOUNTING PLATE E-109492

• Easy and quick mounting (only two screws required)
• Quicker module replacement
• Robust stainless steel plate
• Suitable for doors hinged on the right or left

Mounting plate for evaluation module-control module combination

Suitable for all MGB combinations, comprising an evaluation module and a control module.

Important:Only use if the handle module is also fastened to a mounting plate.

Order numbers:

• 110 072 MGB-A MOUNTING PLATE LC-110072

Order numbers:

• 092 495 RPS-O-8-50/V5

Order numbers:

• 092 496 RPS-RS/V5

Order numbers:

• 092 501 RPS-PS/V5

Order numbers:

• 096 251 RPS-P/V1

Order numbers:

• 092 498 RPS-B-6-60/V5
• 092 500 RPS-B-6-110

Order numbers:

• 092 136 RPS-W-100/175
• 092 138 RPS-W-300

Order numbers:

• 092 813 RPS-I-3-4/50m
• 092 814 RPS-I-3-4/100m

• Housing made of plastic
• Ambient temperature -5 to +60 C

Order numbers:

• 072 828 Holder HBA gray
• 072 935 Holder HBA gray, enlarged handwheel opening
• 100 221 Holder HBA black
• 109 979 Holder HBA black, enlarged handwheel opening

• Housing made of plastic
• Ambient temperature -5 to +60 C

Order numbers:

• 084 397 Holder HBL

Order numbers:

• 112 335 Holder HBM

Order numbers:

• 102 965 Magnet mounting
• 102 969 Screw mounting

Magnetic holder for housing G1

The enabling switches can be attached at any time to any part of the machine due to the magnets fastened to the holder. In this way the enabling switch can be positioned in the activity area as necessary.

Order numbers:

• 059 340 Magnetic holder

Screw holder for housing G1

The holder can be securely fastened to parts of the machine with a wall thickness of max. 15 mm using two screws.

Order numbers:

• 052 406 Holder complete

Screw holder for housing G1 with cable hook

The holder with an additional cable hook for hanging a wound-up cable. It can be securely fastened to parts of the machine with a wall thickness of max. 15 mm using two screws.

Order numbers:

• 047 820 Cable holder

Suitable for GP, SGP, SGA, TP, STP and STA

Order numbers:

• 096 613 Switch bracket TP-GFK