KezdőlapProductsPosition switches and multiple limit switchesMultiple limit switch, upright SNSN04D12-2514-M

SN04D12-2514-M (Rend. sz. 090525)

Válasszon tartalmat Ismertetés Méretrajzok Műszaki adatok Komponensek Tartozékok Letöltési link Rendelési adatok

Series SN... 12 mm, mechanical

Plunger spacing 12 mm
Upright housing, small flange
Degree of protection IP67 according to IEC 60529

Ismertetés

Switching elements

ES 502 E	Snap-action switching contact 1 NC + 1 NO
ES 514	Snap-action switching contact 1 NC + 1 NO

On the usage of safety switching elements, the dog distance must be maintained to achieve the positively driven travel. The dogs must be positively mounted according to EN ISO 14119, i.e. riveted, welded or secured in some other way against becoming loose.

Dimensional drawings

*	Safety switching element ES514 positive opening. Positive opening function is dependent on maintaining this distance.
1	Depending on version
2	Operating point
3	Free position
4	Dog
5	Actuators (dogs) must be connected to the machine in a flush position.
6	Switch can be replaced only with the same type.
7	Pressure sensitive label 041734 applied.
8	Number of plungers

Connection examples

Műszaki adatok

Approvals

CCC_2020980305000540_CQC2008010305306206

Electrical connection values

Connection cross section	0.34 ... 1.5 mm²
Rated insulation voltage U_i	250 V
Rated impulse withstand voltage U_imp	2.5 kV
Utilization category
AC-15	6 A 250 V (applies from station 3 with switching element ES502E)
AC-12	8 A 250 V
DC-13	6 A 24 V
AC-15	2.5 A 230 V (applies to station 1-2 with switching element ES514)
Short circuit protection according to IEC 60269-1
	8A gG (applies from station 3 with switching element ES502E)
	6A gG (applies to station 1-2 with switching element ES514)
Switching current
min. at DC 12V	min. 10 mA (applies from station 3 with switching element ES502E)
min. at DC 24V	min. 5 mA (applies to station 1-2 with switching element ES514)
thermal rated current I_th	8 A

Mechanical values and environment

Approach speed	0.01 ... 40 m/min
Connection type
2 x	M20 x 1.5
Number NC contacts	2
Number of switching elements	4
Number of NO contacts	4
Number of positively driven contacts	2
Design	upright
Actuating element	Chisel plunger (Operating point accuracy ± 0.002. The reproducible operating point accuracy refers to the axial travel of the plunger after the switching element ES 502 E has been run-in with approx. 2,000 operating cycles.)
Actuating force	min. 30 N
Installation orientation	any
Mechanical life	1 x 10⁶
Switching principle
	Snap-action switching contact (Contact closing time<4 ms contact bounce time<3 ms, applies from station 3 with switching element ES502E)
	Snap-action switching contact (Contact closing time ≤ 5 ms, contact bounce time ≤ 3 ms; applies to station 1-2 with switching element ES514)
Degree of protection	IP67
Plunger spacing	12 mm
Ambient temperature	-5 ... +80 °C
Material
Housing	Die-cast aluminum, anodized
Contact	Silver alloy, gold flashed

Characteristic values according to EN ISO 13849-1 and EN IEC 62061

B_10D	2 x 10⁶

B_10D

2 x 10⁶

Miscellaneous

Additional information	Mixed contact assembly (On upright multiple limit switches, it is necessary to start with the safety station/s from the flange side. If several safety stations are to be installed, these must be installed directly one after the other.)

Additional information

Mixed contact assembly (On upright multiple limit switches, it is necessary to start with the safety station/s from the flange side. If several safety stations are to be installed, these must be installed directly one after the other.)

Letöltések

Teljes csomag

Minden fontos dokumentum letöltése egyetlen kattintással.

Tartalom:

A használati utasítás és a használati utasítás vagy a rövid utasítás kiegészítései
A használati utasítást kiegészítő adatlapok
A megfelelőségi nyilatkozat

Teljes csomag letöltése (ZIP, 1,8 MB)