RGBF08X12-732L-M (Sip. No. 110533)

Choose content Açıklama Boyut çizimleri Teknik Veriler Bileşenler Aksesuar İndirme bağlantısı Sipariş verileri

Series RGBF... 12 mm, inductive

Proximity switch spacing 12 mm
Upright housing according to DIN 43697
Degree of protection IP67 according to IEC 60529
LED function display

Açıklama

LED function display

DC and AC switching elements are equipped as standard with a function display on the switching element (yellow). The function display can be seen from the exterior.

Switching element DC NO contact, PNP777, l1 = 12 mm779, l1 = 16 mm

Switching element ES732/4C1997 or ES732/2C1997

Dimensional drawings

1	Actuator
10	Type
11	Length
2	Assured operating distance
3	Label, sequential number
4	Groove with sealing ring
5	LED with NC function of the switching element ES732/2C1997+ES732/4C1997 illuminates if not actuated.
6	Station
7	Switching element
8	Ident no.
9	Number of stations

Connection examples

Teknik Veriler

Approvals

Workspace

Rated operating distances S_n	5 mm
Assured operating distances S_a	0 ... 4 mm (Dimension applies only to steel (ST37) and to EUCHNER trip dogs of series UX.. / GX..)
Switching hysteresis	0.2 ... 1.0 mm (When installed)
Repeat accuracy R
according to EN 60947-5-2	max. 5 %
	Switching element, stations 1 and 5, stations 3 and 7
Center offset
At s = 4 mm	m_OFF= (-) 0.5 mm and m_ON= 0.0 (For side approach)
At s = 1 mm	m_OFF= (-) 4.2 mm and m_ON= (-) 4.0 (For side approach)
At s = 3 mm	m_OFF= (-) 2.5 mm and m_ON= (-) 2.0 (For side approach)
At s = 2 mm	m_OFF= (-) 3.3 mm and m_ON= (-) 3.0 (For side approach)
	Switching element, stations 2 and 6, stations 4 and 8
Center offset
At s = 2 mm	m_ON= (-) 3.3 mm and m_OFF= (-) 3.0 (For side approach)
At s = 1 mm	m_ON= (-) 4.2 mm and m_OFF= (-) 4.0 (For side approach)
At s = 3 mm	m_ON= (-) 2.5 mm and m_OFF= (-) 2.0 (For side approach)
At s = 4 mm	m_ON= (-) 0.5 mm and m_OFF= 0.0 (For side approach)

Operating and display elements

LED display
LED yellow	LED forward current I Fmax. 2.5 mA

Electrical connection values

Output type	PNP
Rated operating current I_e	250 mA
Operating voltage
DC	20 ... 24 ... 33 V Power supply unit with electrical isolation as per EN 61558-2-6 or sensor pulsing U_B(HIGH)
Operating current	max. 5 mA Current consumption without load
EMC protection requirements	EN 60947-5-2
Utilization category
DC-12	250mA, 33V (For DC-13, the output must be protected with a free-wheeling diode for inductive loads.)
Short circuit and overload protection, pulsed	yes
LOW level
on sensor pulsing	0 ... 5 V DC
Off-state current Ir	max. 0.001 mA
Residual ripple
From U_Bor U_B(HIGH)	max. 10 %
Electrical switching frequency	max. 500 Hz
Safety class	I
Voltage drop U_d
DC	max. 2.5 V
Duty cycle T_on
T (HIGH) : T (LOW) on sensor pulsing	4 : 1
Test pulse duration
T (LOW) on sensor pulsing	0.1 ... 20 ms
Reverse polarity protection	yes

Mechanical values and environment

Connection type	Connection terminals on the switching element
Number NC contacts	4
Number of switching elements	8
Number of NO contacts	4
Design	upright
Proximity switch spacing	12 mm
Degree of protection	IP67 (only screwed tight with the related mating connector.)
Ambient temperature	-25 ... +70 °C
Material
Active face	PBT
Housing	Die-cast aluminum

İndirme

Komple paket

Tüm önemli belgeleri tek bir tıklama ile indirin.

İçerik:

Kullanım talimatları ve kullanım talimatlarına veya kısa talimatlara yapılan tüm eklemeler
Kullanım talimatlarını tamamlayan tüm veri sayfaları
Uygunluk beyanı

Paketin tamamını indirin (ZIP, 0,3 MB)