SN02X12-732L-MC2432 (Sip. No. 123939)

Choose content Açıklama Boyut çizimleri Teknik Veriler Bileşenler Aksesuar İndirme bağlantısı Sipariş verileri

Series SN... 12 mm, inductive

With 12 mm proximity switch spacing, the rated operating distance is 5 mm.

The switching elements are equipped as standard with a function display (yellow). The function display can be clearly seen from the exterior.

PE/FE over thread screen connection

1	Attention: Built-in connector not aligned
2	Yellow LED indicator
3	Assured operating distance
4	Actuator
5	without earth conductor
6	Housing without earth conductor! All the electrical connections must either be isolated from the mains supply by a safety transformer according to EN IEC 61558-2-6 with limited output voltage in the event of a fault, or by other equivalent insulation measures.

1	M12 built-in plug connector
2	OV bridge in the switch

Rated operating distances S_n	5 mm
Assured operating distances S_a	0 ... 4 mm (Dimension applies only to steel (ST37) and to EUCHNER trip dogs of series UX.. / GX..)
Center offset
At s = 4 mm	m_ON= (-) 0.5 mm and m_OFF= 0.0 (For side approach)
At s = 3 mm	m_ON= (-) 2.5 mm and m_OFF= (-) 2.0 (For side approach)
At s = 1 mm	m_ON= (-) 4.2 mm and m_OFF= (-) 4.0 (For side approach)
At s = 2 mm	m_ON= (-) 3.3 mm and m_OFF= (-) 3.0 (For side approach)
Switching hysteresis	0.2 ... 1.0 mm (When installed)
Repeat accuracy R
according to EN 60947-5-2	max. 5 %

LED display
LED yellow	LED forward current IFmax. 2.5 mA

Output type	PNP
Rated operating current I_e	250 mA
Operating voltage
DC	20 ... 24 ... 33 V Power supply unit with electrical isolation as per EN 61558-2-6 or sensor pulsing U_B(HIGH)
Operating current	max. 5 mA Current consumption without load
EMC protection requirements	EN 60947-5-2
Utilization category
DC-12	250mA, 33V (For DC-13, the output must be protected with a free-wheeling diode for inductive loads.)
Short circuit and overload protection, pulsed	yes
LOW level
on sensor pulsing	0 ... 5 V DC
Off-state current Ir	max. 0.001 mA
Residual ripple
From U_Bor U_B(HIGH)	max. 10 %
Electrical switching frequency	max. 500 Hz
Safety class	III
Voltage drop U_d
DC	max. 2.5 V
Duty cycle T_on
T (HIGH) : T (LOW) on sensor pulsing	4 : 1
Test pulse duration
T (LOW) on sensor pulsing	0.1 ... 20 ms
Reverse polarity protection	yes

Connection type
	Connection terminals on the switching element
	1 x plug connector M12 (5-pin, straight plug connector: cable outlet not adjustable.)
Number NC contacts	2
Number of switching elements	2
Design	upright
Proximity switch spacing	12 mm
Switching principle	Normally closed contact
Degree of protection	IP67 (only screwed tight with the related mating connector.)
Ambient temperature	-25 ... +70 °C
Material
Housing	Die-cast aluminum
Active face	PBT

C number
C2432
Additional information	Housing without earth conductor! (All the electrical connections must either be isolated from the mains supply by a safety transformer according to EN IEC 61558-2-6 with limited output voltage in the event of a fault, or by other equivalent insulation measures.)

123997
C-M12F05-05X034PU10,0-MA-123997

124054
C-M12F05-05X034PU25,0-MA-124054

Tüm önemli belgeleri tek bir tıklama ile indirin.

İçerik:

Kullanım talimatları ve kullanım talimatlarına veya kısa talimatlara yapılan tüm eklemeler
Kullanım talimatlarını tamamlayan tüm veri sayfaları
Uygunluk beyanı