Safety switch TX ASi, plug connector(s) M12, escape release
- Plug connector(s) M12, 4-pin
- with escape release
- Auxiliary release
- LED indicator
- Closed-circuit current principle
Açıklama
Approach direction
Horizontal and vertical
Can be adjusted in 90° steps
Guard locking principle
closed-circuit current (power to unlock): In a safety guard with guard locking according to the closed-circuit current principle, the guard is locked by spring force until the guard locking solenoid is supplied with current. The guard is unlocked by means of magnetic force. This is also referred to as mechanical guard locking.
Control of the guard locking solenoid
The guard locking solenoid is controlled via AS-Interface bit D0. In order to achieve safe control of the guard locking, the auxiliary voltage must also be switched safely.
auxiliary voltage
The ASi auxiliary voltage is required to supply the guard locking solenoid.
Escape release
This is used for manual release of guard locking from the danger zone without tools.
AS-Interface inputs
D0, D1 | Monitoring of the guard position |
D2, D3 | Monitoring the guard locking |
AS-Interface outputs
D0 | Activating the guard locking |
D1 | LED red |
D2 | LED green |
LED indicator
The Power LED indicates the operating voltage on the bus.
The Fault LED indicates when an error has been detected on the AS-Interface bus.
The green and red LEDs can be controlled by the control system via the bus as required using bits D1 and D2.
Auxiliary release
The auxiliary release on the front allows access to the machine in the event of a malfunction, e.g. a power failure. It is unlocked using a tool or a key. The auxiliary release must be secured against misuse (sealing, laking).
Required accessories
Actuator is not included in the scope of delivery.
Dimensional drawings
| 1 | Auxiliary release |
| 2 | LED indicator |
| 3 | Locking screw |
| 4 | Escape release, basic position |
| 5 | Escape release, unlocked position |
Connection examples
| View of plug side |
Teknik Veriler
Approvals
Electrical connection values
| ASI operating current | max. 45 mA |
| AS-Interface auxiliary voltage | 24 V -15 ... 10 % |
| Auxiliary current AS-Interface | 300 mA |
| AS-Interface protocol | ASi-3 |
| ASI data out | D0 = control of guard locking, D1 = red LED, D2 = green LED |
| ASI data in | D0, D1 = door position, D2, D3 = guard locking |
| AS-Interface slave type | ID-Code: B, EA-Code: 7 |
| ASI voltage | 22.5 ... 30 ... 31.6 V |
| Solenoid duty cycle | 100 % |
Mechanical values and environment
| Approach speed | max. 20 m/min |
| Connection type | |
| 1 x | Plug connector M12 (4-pin) |
| Number of door position positively driven contacts | |
| according to AS-i Safety at Work | |
| Number of guard lock monitoring positively driven contacts | |
| according to AS-i Safety at Work | 1 D2,D3 (1 = locked) |
| Extraction force | 35 N |
| Actuation frequency | max. 1200 1/h |
| Actuating force | 35 N |
| Installation orientation | any |
| Insertion depth | 32 mm |
| Mechanical life | 1 x 10⁶ |
| Retention force | 20 N |
| Switching principle | Slow-action switching contact |
| Degree of protection | IP67 |
| Ambient temperature | -20 ... +50 °C |
| Material | |
| Housing | Die-cast alloy cathodically dipped |
| Contact | Silver alloy, gold flashed |
| Guard locking principle | Closed-circuit current principle |
Characteristic values according to EN ISO 13849-1 and EN IEC 62061
| B10D | Mission time | |
|---|---|---|
| Monitoring of the guard position | 5x106 | 20 y |
| Important! Values valid at DC-13 100 mA/24V | ||
| Monitoring of guard locking | 5x106 | 20 y |
| Important! Values valid at DC-13 100 mA/24V | ||
Miscellaneous
| C number | |
| C1991 | Escape release |
In combination with actuator ACTUATOR-X-GNQ
| Overtravel | 8 mm |
In combination with actuator ACTUATOR-X-GQ
| Overtravel | 1 mm |
Aksesuar
RIEGEL TX-AF
- Bolt for safety switch with escape release TX...C1991 and 2161
- Steel bolt
- For doors hinged on the right
- escape lever
- Detent knob in open position
- Suitable for a door gap of approx. 15 mm
RIEGEL TX-CF
- Bolt for safety switch with escape release TX...C1991 and 2161
- Steel bolt
- For doors hinged on the left
- escape lever
- Detent knob in open position
- Suitable for a door gap of approx. 15 mm
İndirme
Komple paket
Tüm önemli belgeleri tek bir tıklama ile indirin.
İçerik:
- Kullanım talimatları ve kullanım talimatlarına veya kısa talimatlara yapılan tüm eklemeler
- Kullanım talimatlarını tamamlayan tüm veri sayfaları
- Uygunluk beyanı
Tek Belgeler
Déclaration UE de conformité
Declaración de conformidad UE
EU-Konformitätserklärung
Dichiarazione UE di conformità
Déclaration UE de conformité
Declaración de conformidad UE
EU-Konformitätserklärung
Dichiarazione UE di conformità
Mode d’emploi Interrupteur de sécurité TX…AS1
Manual de instrucciones Interruptor de seguridad TX…AS1
Betriebsanleitung Sicherheitsschalter TX…AS1
Diğer Belgeler
CAD Verileri
Sipariş verileri
| Sip. No. | 095914 |
| Makale adı | TX1B-A024SEM4AS1C1991 |
| Ağırlık | 0,936kg |
| Gümrük sınıfı | 85365019000 |
| ECLASS | 27-27-26-03 Safety switch with guard control |
